Source Code
|
These source-code files are part of a reconstructed copy of Luminary 97, the
original release of the Apollo 11 Lunar Module (LM) Apollo Guidance Computer
(AGC) software.
The reconstruction began with source code of Luminary 99 revision 1 previously
transcribed from a digitized copy of that program. The code was then updated
by undoing changes described in original Luminary memos 83 and 85, using asterisks
indicating changed lines in the listing as a guide. The reconstruction was
verified by matching memory-bank checksums to those listed in drawing 2021152D.
Note that page numbers in the reconstructed code match those on the Luminary 099
revision 001 printout, although the added code would likely have changed page
numbers for a real Luminary 97 listing.
Comments from the original source code are prefixed with a single '#' symbol,
whereas comments added later are prefixed by "##" or "###". Report any errors
noted by creating an
issue report at the Virtual AGC
project's GitHub repository.
|
057804,000002: ## Copyright: Public domain.
057805,000003: ## Filename: SERVICE_ROUTINES.agc
057806,000004: ## Purpose: A section of Luminary revision 97.
057807,000005: ## It is part of the reconstructed source code for the
057808,000006: ## original release of the flight software for the Lunar
057809,000007: ## Module's (LM) Apollo Guidance Computer (AGC) for Apollo 11.
057810,000008: ## The code has been recreated from a copy of Luminary 99
057811,000009: ## revision 001, using asterisks indicating changed lines in
057812,000010: ## the listing and Luminary Memos #83 and #85, which list
057813,000011: ## changes between Luminary 97 and 98, and 98 and 99. The
057814,000012: ## code has been adapted such that the resulting bugger words
057815,000013: ## exactly match those specified for Luminary 97 in NASA drawing
057816,000014: ## 2021152D, which gives relatively high confidence that the
057817,000015: ## reconstruction is correct.
057818,000016: ## Reference: pp. 1374-1380
057819,000017: ## Assembler: yaYUL
057820,000018: ## Contact: Ron Burkey <info@sandroid.org>.
057821,000019: ## Website: www.ibiblio.org/apollo/index.html
057822,000020: ## Mod history: 2019-07-28 MAS Created from Luminary 99.
057823,000021:
|
|
Page 1374
|
057825,000023: 10,3544 BANK 10
057826,000024: 10,2000 SETLOC DISPLAYS
057827,000025: 10,2000 BANK
057828,000026: 10,3544 COUNT* $$/DSPLA
057829,000027:
057830,000028: 10,3544 00004 UPENT2 INHINT
057831,000029: 10,3545 75660 MASK OCT77770
057832,000030: 10,3546 54001 TS L
057833,000031: 10,3547 40100 CS FLAGWRD4
057834,000032: 10,3550 70001 MASK L
057835,000033: 10,3551 26100 ADS FLAGWRD4
057836,000034: 10,3552 00003 JOIN RELINT
057837,000035: 10,3553 16737 TCF Q+1
057838,000036:
057839,000037: 10,3554 00004 DOWNENT2 INHINT
057840,000038: 10,3555 75660 MASK OCT77770
057841,000039: 10,3556 40000 COM
057842,000040: 10,3557 70100 MASK FLAGWRD4
057843,000041: 10,3560 54100 TS FLAGWRD4
057844,000042: 10,3561 13552 TCF JOIN
057845,000043:
057846,000044: 10,3562 4757 OCT7 EQUALS SEVEN
057847,000045:
|
|
Page 1375
|
057849,000047: # UPFLAG AND DOWNFLAG ARE ENTIRELY GENERAL FLAG SETTING AND CLEARING SUBROUTINES. USING THEM, WHETHER OR
057850,000048: # NOT IN INTERRUPT, ONE MAY SET OR CLEAR ANY SINGLE, NAMED BIT IN ANY ERASABLE REGISTER, SUBJECT OF COURSE TO
057851,000049: # EBANK SETTING. A "NAMED" BIT, AS THE WORD IS USED HERE, IS ANY BIT WITH A NAME FORMALLY ASSIGNED BY THE YUL
057852,000050: # ASSEMBLER.
057853,000051:
057854,000052: # AT PRESENT THE ONLY NAMED BITS ARE THOSE IN THE FLAGWORDS. ASSEMBLER CHANGES WILL MAKE IT POSSIBLE TO
057855,000053: # NAME ANY BIT IN ERASABLE MEMORY.
057856,000054:
057857,000055: # CALLING SEQUENCES ARE AS FOLLOWS :-
057858,000056: # TC UPFLAG TC DOWNFLAG
057859,000057: # ADRES NAME OF FLAG ADRES NAME OF FLAG
057860,000058:
057861,000059: # RETURN IS TO THE LOCATION FOLLOWING THE "ADRES" ABOUT .58 MS AFTER THE "TC".
057862,000060: # UPON RETURN A CONTAINS THE CURRENT FLAGWRD SETTING.
057863,000061:
057864,000062: 5504 BLOCK 02
057865,000063: 4000 SETLOC FFTAG1
057866,000064: 4000 BANK
057867,000065: 5504 COUNT* $$/FLAG
057868,000066:
057869,000067: 5504 30002 UPFLAG CA Q
057870,000068: 5505 05522 TC DEBIT
057871,000069: 5506 40000 COM # +(15 - BIT)
057872,000070: 5507 00006 EXTEND
057873,000071: 5510 04001 ROR LCHAN # SET BIT
057874,000072: 5511 50061 COMFLAG INDEX ITEMP1
057875,000073: 5512 54074 TS FLAGWRD0
057876,000074: 5513 22063 LXCH ITEMP3
057877,000075: 5514 00003 RELINT
057878,000076: 5515 00001 TC L
057879,000077:
057880,000078: 5516 30002 DOWNFLAG CA Q
057881,000079: 5517 05522 TC DEBIT
057882,000080: 5520 70001 MASK L # RESET BIT
057883,000081: 5521 15511 TCF COMFLAG
057884,000082:
057885,000083: 5522 64753 DEBIT AD ONE # GET DE BITS
057886,000084: 5523 00004 INHINT
057887,000085: 5524 54063 TS ITEMP3
057888,000086: 5525 34762 CA LOW4 # DEC15
057889,000087: 5526 54061 TS ITEMP1
057890,000088: 5527 50063 INDEX ITEMP3
057891,000089: 5530 27777 CA 0 -1 # ADRES
057892,000090: 5531 54001 TS L
057893,000091: 5532 34755 CA ZERO
|
|
Page 1376
|
057895,000093: 5533 00006 EXTEND
057896,000094: 5534 10061 DV ITEMP1 # A = FLAGWRD, L = (15 - BIT)
057897,000095: 5535 52062 DXCH ITEMP1
057898,000096: 5536 50061 INDEX ITEMP1
057899,000097: 5537 30074 CA FLAGWRD0
057900,000098: 5540 54001 TS L # CURRENT STATE
057901,000099: 5541 50062 INDEX ITEMP2
057902,000100: 5542 44735 CS BIT15 # -(15 - BIT)
057903,000101: 5543 00002 TC Q
057904,000102:
|
|
Page 1377
|
057906,000104: # DELAYJOB - A GENERAL ROUTINE TO DELAY A JOB A SPECIFIC AMOUNT OF TIME BEFORE PICKING UP AGAIN.
057907,000105:
057908,000106: # ENTRANCE REQUIREMENTS ...
057909,000107: # CAF DT DELAY JOB FOR DT CENTISECS
057910,000108: # TC BANKCALL
057911,000109: # CADR DELAYJOB
057912,000110:
057913,000111: 06,3764 BANK 06
057914,000112: 00,2000 SETLOC DLAYJOB
057915,000113: 00,2000 BANK
057916,000114:
057917,000115: # THIS MUST REMAIN IN BANK 0 *****************************************
057918,000116:
057919,000117: 00,3735 COUNT* $$/DELAY
057920,000118: 00,3735 00004 DELAYJOB INHINT
057921,000119: 00,3736 54002 TS Q # STORE DELAY DT IN Q FOR DLY -1 IN
057922,000120: 00,3737 34752 CAF DELAYNUM # WAITLIST
057923,000121: 00,3740 54070 DELLOOP TS RUPTREG1
057924,000122: 00,3741 50000 INDEX A
057925,000123: 00,3742 31326 CA DELAYLOC # IS THIS DELAYLOC AVAILABLE
057926,000124: 00,3743 00006 EXTEND
057927,000125: 00,3744 13752 BZF OK2DELAY # YES
057928,000126:
057929,000127: 00,3745 10070 CCS RUPTREG1 # NO, TRY NEXT DELAYLOC
057930,000128: 00,3746 13740 TCF DELLOOP
057931,000129:
057932,000130: 00,3747 52134 DXCH BUF2
057933,000131: 00,3750 05716 TC BAILOUT1 # NO AVAILABLE LOCS.
057934,000132: 00,3751 01104 OCT 1104
057935,000133:
057936,000134: 00,3752 33772 OK2DELAY CA TCSLEEP # SET WAITLIST IMMEDIATE RETURN
057937,000135: 00,3753 54061 TS WAITEXIT
057938,000136:
057939,000137: 00,3754 30004 CA FBANK
057940,000138: 00,3755 60070 AD RUPTREG1 # STORE BBANK FOR TASK CALL
057941,000139: 00,3756 54001 TS L
057942,000140:
057943,000141: 00,3757 33773 CAF WAKECAD # STORE CADR FOR TASK CALL
057944,000142: 00,3760 15211 TCF DLY2 -1 # DLY IS IN WAITLIST ROUTINE
057945,000143:
057946,000144: 00,3761 04645 TCGETCAD TC MAKECADR # GET CALLERS FCADR
057947,000145:
057948,000146: 00,3762 50070 INDEX RUPTREG1
057949,000147: 00,3763 55326 TS DELAYLOC # SAVE DELAY CADRS
057950,000148:
057951,000149: 00,3764 05133 TC JOBSLEEP
057952,000150:
057953,000151: 00,3765 34755 WAKER CAF ZERO
057954,000152: 00,3766 50006 INDEX BBANK
057955,000153: 00,3767 57326 XCH DELAYLOC # MAKE DELAYLOC AVAILABLE
|
|
Page 1378
|
057957,000155: 00,3770 05137 TC JOBWAKE
057958,000156:
057959,000157: 00,3771 05261 TC TASKOVER
057960,000158:
057961,000159: 00,3772 03757 TCSLEEP GENADR TCGETCAD -2
057962,000160: 00,3773 03765 WAKECAD GENADR WAKER
057963,000161:
|
|
Page 1379
|
057965,000163: # GENTRAN, A BLOCK TRANSFER ROUTINE.
057966,000164: # WRITTEN BY D. EYLES
057967,000165: # MOD 1 BY KERNAN UTILITYM REV 17 11/18/67
057968,000166: # MOD 2 BY SCHULENBERG (REMOVE RELINT) SKIPPER REV 4 2/28/68
057969,000167:
057970,000168: # THIS ROUTINE IS USEFULL FOR TRANSFERING N CONSECUTIVE ERASABLE OR FIXED QUANTITIES TO SOME OTHER N
057971,000169: # CONSECUTIVE ERASABLE LOCATIONS. IF BOTH BLOCKS OF DATA ARE IN SWITCHABLE EBANKS, THEY MUST BE IN THE SAME ONE.
057972,000170:
057973,000171: # GENTRAN IS CALLABLE IN A JOB AS WELL AS A RUPT. THE CALLING SEQUENCE IS:
057974,000172: # I CA N-1 # OF QUANTITIES MINUS ONE.
057975,000173: # I +1 TC GENTRAN IN FIXED-FIXED.
057976,000174: # I +2 ADRES L STARTING ADRES OF DATA TO BE MOVED.
057977,000175: # I +3 ADRES M STARTING ADRES OF DUPLICATION BLOCK.
057978,000176: # I +4 RETURNS HERE.
057979,000177:
057980,000178: # GENTRAN TAKES 25 MCT'S (300 MICROSECONDS) PER ITEM + 5 MCT'S (60 MICS) FOR ENTERING AND EXITING.
057981,000179: # A, L AND ITEMP1 ARE NOT PRESERVED.
057982,000180:
057983,000181: 5544 BLOCK 02
057984,000182: 4000 SETLOC FFTAG4
057985,000183: 4000 BANK
057986,000184:
057987,000185: 5544 0061 EBANK= ITEMP1
057988,000186:
057989,000187: 5544 COUNT* $$/TRAN
057990,000188:
057991,000189: 5544 00004 GENTRAN INHINT
057992,000190: 5545 54061 TS ITEMP1 # SAVE N-1.
057993,000191: 5546 50002 INDEX Q # C(Q) = ADRES L.
057994,000192: 5547 60000 AD 0 # ADRES (L + N - 1).
057995,000193: 5550 50000 INDEX A
057996,000194: 5551 30000 CA 0 # C(ABOVE).
057997,000195: 5552 54001 TS L # SAVE DATA.
057998,000196: 5553 30061 CA ITEMP1
057999,000197: 5554 50002 INDEX Q
058000,000198: 5555 60001 AD 1 # ADRES (M + N - 1).
058001,000199: 5556 50000 INDEX A
058002,000200: 5557 22000 LXCH 0 # STUFF IT.
058003,000201: 5560 10061 CCS ITEMP1 # LOOP UNTIL N-1 = 0.
058004,000202: 5561 15545 TCF GENTRAN +1
058005,000203: 5562 16741 TCF Q+2 # RETURN TO CALLER.
058006,000204:
|
|
Page 1380
|
058008,000206: # B5OFF ZERO BIT 5 OF EXTVBACT, WHICH IS SET BY TESTXACT.
058009,000207: # MAY BE USED AS NEEDED BY ANY EXTENDED VERB WHICH HAS DONE TESTXACT
058010,000208:
058011,000209: 5563 COUNT* $$/EXTVB
058012,000210:
058013,000211: 5563 44747 B5OFF CS BIT5
058014,000212: 5564 71044 MASK EXTVBACT
058015,000213: 5565 55044 TS EXTVBACT
058016,000214: 5566 05155 TC ENDOFJOB
058017,000215:
058018,000216:
058019,000217:
End of include-file SERVICE_ROUTINES.agc. Parent file is MAIN.agc